Whole Home Backup
Disclaimer: For reference only. Consult a licensed professional.
Battery bank sizing for a Whole Home Backup in 2026
A typical Whole Home Backup consumes about 30 kWh per day across full home including HVAC compressor, electric water heater, cooking range, laundry, all lighting and outlets. True whole-home backup is rare and expensive — it requires 40+ kWh of storage and a 10+ kW inverter to run AC compressors and cooking simultaneously. Tesla Powerwall 3 stacks at 13.5 kWh each. The design focus for this use case is massive continuous output for HVAC compressor support, parallel inverter configurations for surge handling, multi-day autonomy through extended outages. Year-round operation; summer AC and winter heating are both fully supported.
Working through the sizing math: at 30 kWh per day with 1 day of autonomy and 85 percent depth-of-discharge for LiFePO4, the bank needs to store roughly 35.3 kWh of nominal capacity. At 48V that converts to 735 Ah. Combined with the peak instantaneous load of 10,000W and motor-startup surge of 16,000W, the recommended configuration covers the use case end-to-end.
Daily load profile for a whole home
Continuous high load 16-18 hours per day; lower overnight baseline; peaks at meal and laundry times. The primary loads breaking down by typical contribution:
- Central AC compressor (3500W run, 9000W LRA)
- Electric water heater (4500W cycling)
- Electric range (12000W max, intermittent)
- Refrigerator + freezer (250W cycling)
- Whole-house lighting and outlets (500-1500W varies)
Total daily energy is approximately 30 kWh, with peak instantaneous demand of 10,000W typically occurring during simultaneous appliance operation. Battery banks must support both daily energy needs and momentary peaks; the latter often forces a larger inverter than daily energy alone would suggest.
Step-by-step sizing calculation
Step 1 — Daily energy in amp-hours
Daily Ah = (30 x 1000) / 48
Daily Ah = 625 Ah/day
Step 2 — Total bank capacity
Bank Ah = 625 x 1 / 0.85
Bank Ah = 735 Ah
The 0.85 factor reflects 85 percent depth-of-discharge, the practical maximum for LiFePO4 chemistry without significantly shortening cycle life. Lead-acid would use 0.5 here, requiring roughly double the rated capacity for the same usable energy.
Step 3 — Inverter sizing
Surge rating ≥ Largest motor LRA = 16,000W
Pump and motor loads have locked-rotor amps of 4 to 7 times running current; surge rating becomes the binding constraint rather than continuous rating.
Step 4 — Solar array sizing
Solar W needed = 30 x 1000 / (5 x 0.78)
Solar W needed ≈ 10000W
The 0.78 factor accounts for real-world losses: inverter conversion (3 to 5 percent), DC wiring (1 to 2 percent), soiling (2 to 5 percent), temperature derating (5 to 10 percent), and shading and azimuth deviation. For climates with fewer than 4.5 peak sun hours in winter, oversize panel wattage by 25 to 40 percent to bridge the lowest production months.
Recommended bill of materials (Q1 2026 pricing)
The complete system below is sized for the Whole Home Backup requirements above. All prices are Q1 2026 reseller list prices in US dollars; actual costs vary by region and shop. Distributor channels (Signature Solar, Wholesale Solar, Battle Born direct) often discount 5 to 15 percent from list.
| Component | Product | Specification | Qty | Subtotal |
|---|---|---|---|---|
| Battery bank | EG4 LL-S 48V 100Ah | 100 Ah / 5.12 kWh each | 12 | $12,588 |
| Inverter / charger | Sol-Ark 12K | 12,000W cont / 18,000W surge | 1 | $6,800 |
| Solar charge controller | Victron SmartSolar MPPT 100/30 | 30A output | 1 | $250 |
| Solar panels | REC Alpha Pure-R 410W | 410W each, 10.3 kW total | 25 | $7,750 |
| Balance of system | Class T fuse, MRBF terminal fuses, breakers, DC bus, 4/0 AWG copper, enclosure | Varies | 1 lot | $2,150 |
| Total parts cost (excluding labor) | $29,538 | |||
Balance-of-system covers a Class T fuse on the battery positive terminal (essential for LiFePO4 short-circuit protection), MRBF terminal fuses on each battery, a main DC disconnect, bus bars, 4/0 AWG copper for the high-current battery-to-inverter run, and an enclosure or rack.
Three budget tiers for the same use case
Solar pairing and daily recharge
For grid-disconnected operation, the solar array must replenish daily consumption plus losses. At 5 peak sun hours per day (US average) and 78 percent system efficiency, 10000W of PV produces approximately 39 kWh on a typical day — enough to refill the daily load plus margin for battery round-trip loss.
For cloudy stretches, plan additional storage rather than additional panels: a generator or grid hookup costs less per kWh during the worst week of winter than oversizing solar for that one period. Common pitfalls include HVAC compressor surge tripping inverter, no AFCI/GFCI coordination between battery system and existing panel, fire-rated wall required for indoor battery install above certain kWh thresholds per local AHJ.
NEC code compliance for whole home battery systems
NEC Article 706 governs energy storage systems above 1 kWh of stored energy. This bank at 52.2 kWh falls under Article 706 requirements including disconnecting means within sight of the ESS, working space (3 ft front clearance), UL 9540 listing for the full ESS or UL 1973 for individual cells, and arc-flash labeling.
NEC Article 690 covers the solar PV portion: 690.7 sets maximum system voltage, 690.8 conductor sizing at 156 percent of Isc (1.25 continuous x 1.25 irradiance), and 690.9 overcurrent protection. NEC Article 480 applies to battery installation generally, including ventilation, spacing, and overcurrent.
For grid-tied operation, NEC Article 705 adds interconnection rules: anti-islanding, disconnects accessible to utility personnel, and labeling. Major electrical work; full permitting and inspection. Many jurisdictions require fire suppression near ESS over 20 kWh.
Common failure modes and design considerations
The most expensive battery system failures are not from spectacular events but from quiet design oversights:
- Cold-soak BMS cutoff. LiFePO4 BMS will stop charging below 0°C (32°F) and stop discharging below -20°C (-4°F) to protect cells from lithium plating. Battery banks in unconditioned spaces need either self-heating cells or a small thermostatically-controlled heating element drawing 30 to 60W.
- DC bus undersizing. At 48V and 16,000W surge, momentary current peaks reach 333A. Use 4/0 AWG copper minimum on the battery-to-inverter run, keep length under 10 feet, and include a Class T fuse rated for the surge current.
- Inverter idle draw. Even high-quality inverters draw 30 to 50W continuously when on. Over 24 hours that is 0.7 to 1.2 kWh, which on a small system can be 15 to 25 percent of total daily consumption. Use search-mode or remote-switching to disable the inverter overnight when loads are minimal.
- Mismatched parallel batteries. Connecting batteries of different ages or capacities causes current imbalance, with the weakest unit doing most of the cycling. Always match batteries within the same purchase batch.
- Specific to whole home: HVAC compressor surge tripping inverter, no AFCI/GFCI coordination between battery system and existing panel, fire-rated wall required for indoor battery install above certain kWh thresholds per local AHJ.
Maintenance schedule and 10-year lifecycle
LiFePO4 batteries are essentially maintenance-free for the first 8 to 10 years. The typical service schedule:
- Monthly: visual inspection for swelling or terminal corrosion (under 30 seconds per battery).
- Annually: torque-check terminal connections to manufacturer spec (typically 10 to 15 Nm), verify BMS firmware via app or USB, and clean accessible vents and dust filters in the enclosure.
- Year 5 to 7: capacity test if any unusual runtime degradation is suspected. Discharge a battery from 100 to 20 percent state-of-charge at a known load and time it; capacity has degraded if runtime is 15+ percent less than original.
- Year 8 to 12: begin planning replacement. LiFePO4 typically reaches 80 percent of original capacity at this stage; still usable but with reduced runtime.
- Inverter capacitors: capacitor aging affects inverter performance starting around year 10 to 12. Replacement is the typical end-of-life event for the inverter, often costing $200 to $400 in parts.
Frequently asked questions about Whole Home Backup battery systems
How many kWh of battery do I need for a Whole Home Backup?
For a typical Whole Home Backup using 30 kWh per day with 1 day of autonomy, plan on roughly 35.3 kWh of nominal LiFePO4 capacity, which works out to about 735 Ah at 48V. The 0.85 in the math is the depth-of-discharge limit; lead-acid would need roughly twice that nominal capacity for the same usable energy.
What system voltage should I use for a Whole Home Backup?
48V is recommended for this use case. 48V is the modern standard for off-grid and home battery installations because lower current means smaller conductors, lower I-squared-R losses, and broader compatibility with quality inverters and charge controllers. Switching to a higher voltage system later requires replacing batteries, inverter, and charge controller; getting voltage right at the start matters.
What does a Whole Home Backup battery system cost in 2026?
Complete parts cost for the recommended configuration above runs approximately $29,538 at Q1 2026 prices. This breaks down as roughly $12,588 for batteries, $6,800 for the inverter, $250 for the solar charge controller, $7,750 for solar panels, and $2,150 for balance-of-system (cables, fuses, breakers, enclosure). Add 30 to 50 percent for professional installation labor; DIY builds avoid the labor cost but require permits and inspection in most jurisdictions.
What inverter size for a whole home?
The Sol-Ark 12K at 12,000W continuous and 18,000W surge handles this use case. The continuous rating must cover sustained simultaneous load (10,000W for whole home use); the surge rating must cover the largest motor locked-rotor amps (16,000W). Motor surge is the binding constraint here; never undersize the surge spec to save money.
How long do LiFePO4 batteries last in a whole home application?
Quality LiFePO4 batteries deliver 3,000 to 5,000 cycles to 80 percent of original capacity when cycled to 80 percent depth-of-discharge. For a Whole Home Backup cycling roughly once per day, that translates to 10 to 14 years of service before noticeable runtime reduction. Higher-end batteries (Battle Born, Discover AES) carry 10-year warranties; mid-tier products typically warranty 5 to 7 years.
How many solar panels do I need to recharge daily?
At 5 peak sun hours per day average and 78 percent system efficiency, 10000W of solar panels produce roughly 39 kWh per day — sufficient to recharge 30 kWh of consumption plus round-trip losses. That works out to 25 panels at 410W each. For climates with fewer than 4.5 winter peak sun hours, oversize the array by 25 to 40 percent to handle the lowest-production months.
Do I need a permit to install a battery system?
Major electrical work; full permitting and inspection. Many jurisdictions require fire suppression near ESS over 20 kWh. In most US jurisdictions, any battery system above 1 kWh of stored energy triggers NEC Article 706 ESS requirements and needs a permit plus AHJ (Authority Having Jurisdiction) inspection. This bank at 52.2 kWh exceeds that threshold and will require permitting in nearly all areas.
What chemistry should I avoid?
Flooded lead-acid is generally not the right choice for modern off-grid installations. Cycle life is limited to 500 to 1,000 cycles compared to 3,000+ for LiFePO4; usable energy is half (50 percent DoD vs 85 percent for LiFePO4); and flooded cells require monthly water-level checks plus ventilated battery boxes. AGM lead-acid is acceptable for short-term or budget-constrained builds but still loses to LiFePO4 on weight, cycle life, and total cost of ownership over 10 years.